Template:LoadConfig - Revision history

Mellinger at 14:54, 24 October 2008

2008-10-24T14:54:59Z

← Older revision		Revision as of 14:54, 24 October 2008
Line 1:		Line 1:
	*In the ~~operator module~~, click ~~"Config".~~		*In the configuration window, click "Load Parameters", and load the system-specific parameter file [[User_Tutorial:EEG_Measurement_Setup#Inspecting_EEG_Signals\|saved previously]] at <tt>parms/fragments/<YourSystem>.prm</tt>.
	*Click "Load Parameters", and load the system-specific parameter file [[User_Tutorial:EEG_Measurement_Setup#Inspecting_EEG_Signals\|saved previously]] at <tt>parms/fragments/<YourSystem>.prm</tt>.
	*Again, click "Load Parameters" to load <tt>{{{paramfile}}}</tt>.		*Again, click "Load Parameters" to load <tt>{{{paramfile}}}</tt>.
	*When you have a separate monitor for experimenter and subject, load the parameter file at <tt>parms/fragments/stdlib/DualMonitor.prm</tt>.		*When you have a separate monitor for experimenter and subject, load the parameter file at <tt>parms/fragments/stdlib/DualMonitor.prm</tt>.

Mellinger at 14:53, 24 October 2008

2008-10-24T14:53:24Z

← Older revision		Revision as of 14:53, 24 October 2008
Line 1:		Line 1:
			*In the operator module, click "Config".
	*Click "Load Parameters", and load the system-specific parameter file [[User_Tutorial:EEG_Measurement_Setup#Inspecting_EEG_Signals\|saved previously]] at <tt>parms/fragments/<YourSystem>.prm</tt>.		*Click "Load Parameters", and load the system-specific parameter file [[User_Tutorial:EEG_Measurement_Setup#Inspecting_EEG_Signals\|saved previously]] at <tt>parms/fragments/<YourSystem>.prm</tt>.
	*Again, click "Load Parameters" to load <tt>{{{paramfile}}}</tt>.		*Again, click "Load Parameters" to load <tt>{{{paramfile}}}</tt>.

Mellinger: Template:ConfigureSystemSpecificParameters moved to Template:LoadConfig

2008-10-24T14:51:23Z

Template:ConfigureSystemSpecificParameters moved to Template:LoadConfig

← Older revision		Revision as of 14:51, 24 October 2008
(No difference)

Mellinger at 14:49, 24 October 2008

2008-10-24T14:49:54Z

← Older revision		Revision as of 14:49, 24 October 2008
Line 1:		Line 1:
	*~~Again, click~~ "Load Parameters", and load the system-specific parameter file [[User_Tutorial:EEG_Measurement_Setup#Inspecting_EEG_Signals\|saved previously]] at <tt>parms/fragments/<YourSystem>.prm</tt>.		*Click "Load Parameters", and load the system-specific parameter file [[User_Tutorial:EEG_Measurement_Setup#Inspecting_EEG_Signals\|saved previously]] at <tt>parms/fragments/<YourSystem>.prm</tt>.
			*Again, click "Load Parameters" to load <tt>{{{paramfile}}}</tt>.
	*When you have a separate monitor for experimenter and subject, load the parameter file at <tt>parms/fragments/stdlib/DualMonitor.prm</tt>.		*When you have a separate monitor for experimenter and subject, load the parameter file at <tt>parms/fragments/stdlib/DualMonitor.prm</tt>.
	**In your system's display properties configuration, make sure that the subject's monitor is configured to be located to the right of the main monitor.		**In your system's display properties configuration, make sure that the subject's monitor is configured to be located to the right of the main monitor.
	**Make sure the ''WindowLeft'' parameter matches the main monitor's actual pixel width.		**Make sure the ''WindowLeft'' parameter matches the main monitor's actual pixel width.
	**You may need to adapt ''WindowTop'', ''WindowWidth'', and ''WindowHeight'' parameters as well; click "Set Config" to try the effect of your changes.		**You may need to adapt ''WindowTop'', ''WindowWidth'', and ''WindowHeight'' parameters as well; click "Set Config" to try the effect of your changes.

Mellinger at 14:46, 24 October 2008

2008-10-24T14:46:07Z

New page

*Again, click "Load Parameters", and load the system-specific parameter file [[User_Tutorial:EEG_Measurement_Setup#Inspecting_EEG_Signals|saved previously]] at <tt>parms/fragments/<YourSystem>.prm</tt>.
*When you have a separate monitor for experimenter and subject, load the parameter file at <tt>parms/fragments/stdlib/DualMonitor.prm</tt>.
**In your system's display properties configuration, make sure that the subject's monitor is configured to be located to the right of the main monitor.
**Make sure the ''WindowLeft'' parameter matches the main monitor's actual pixel width.
**You may need to adapt ''WindowTop'', ''WindowWidth'', and ''WindowHeight'' parameters as well; click "Set Config" to try the effect of your changes.